摘要： <H3c>reset saved-configuration 重置配置文件。 The saved configuration file will be erased. Are you sure? [Y/N]:Y
Configuration file in cfa0 is being cleared.
Please wait ...
Configuration file is cleared...
<H3c>reset saved-configuration 重置配置文件。
The saved configuration file will be erased. Are you sure? [Y/N]:Y
Configuration file in cfa0 is being cleared.
Please wait ...
Configuration file is cleared.
<H3c>reboot 重新防火墙
Start to check configuration with next startup configuration file, please wait.........DONE!
This command will reboot the device. Current configuration will be lost, save current configuration? [Y/N]:y 这条命令将重启设备，当前配置将丢失，保存当前配置。如果输入Y，就把当前配置保存，不删除。重新启动设置后，配置文件还在。
Please input the file name(*.cfg)[cfa0:/startup.cfg]
(To leave the existing filename unchanged, press the enter key):
Validating file. Please wait....
Configuration is saved to device successfully.
This command will reboot the device. Continue? [Y/N]:
Before pressing ENTER you must choose 'YES' or 'NO'[Y/N]:y
如果选择N。配置文件都将被清除。
<H3C>display current-configuration
#
version 5.20, Release 5140
#
sysname H3C
#
undo voice vlan mac-address 00e0-bb00-0000
#
domain default enable system
#
port-security enable
#
undo alg dns
undo alg rtsp
undo alg h323
undo alg sip
undo alg sqlnet
undo alg pptp
undo alg ils
undo alg nbt
undo alg msn
undo alg qq
undo alg tftp
undo alg sccp
undo alg gtp
#
session synchronization enable
#
password-recovery enable
#
vlan 1
#
domain system
access-limit disable
state active
idle-cut disable
self-service-url disable
#
pki domain default
crl check disable
#
user-group system
group-attribute allow-guest
#
local-user admin
艾泰主路由器 AC控制器旁路调试图解实现教程
今天接到一客户电话，说自己买的艾泰路由器不会设置，于是上门查看原因，原因客户买了一套艾泰企业级路由器，无线AC控制器和两个AP。客户不知道怎么弄。虽说不是怎么难调的事情，对于
password cipher $c$3$e401WU4JJRyE5hqvegXeVHbNniJmLyq1
authorization-attribute level 3
service-type telnet
service-type web
#
cwmp
undo cwmp enable
#
interface NULL0
#
interface GigabitEthernet0/0
port link-mode route
ip address 192.168.0.1 255.255.255.0
#
interface GigabitEthernet0/1
port link-mode route
#
interface GigabitEthernet0/2
port link-mode route
#
interface GigabitEthernet0/3
port link-mode route
#
interface GigabitEthernet0/4
port link-mode route
#
vd Root id 1
#
zone name Management id 0
priority 100
import interface GigabitEthernet0/0
zone name Local id 1
priority 100
zone name Trust id 2
priority 85
zone name DMZ id 3
priority 50
zone name Untrust id 4
priority 5
switchto vd Root
zone name Management id 0
ip virtual-reassembly
zone name Local id 1
ip virtual-reassembly
zone name Trust id 2
ip virtual-reassembly
zone name DMZ id 3
ip virtual-reassembly
zone name Untrust id 4
ip virtual-reassembly
#
load xml-configuration
#
load tr069-configuration
#
user-interface con 0
user-interface vty 0 4
authentication-mode scheme
#
return
<H3C>
桥接和中继哪个速度快
桥接是主流的成熟技术,因此速度和稳定性都好于中继模式。原因：桥接是人工指定了WIFI接入点，中继是自动根据信号强度判断WIFI接入点。中继增加了数据传输的验证关卡，而且稳定性也不
